Makstton Vehicle Fitment Guide

ZEEKR 001 Wheel
Fitment Guide

The ZEEKR 001 is an excellent car, but its rapid update cycle can be frustrating even for a Chinese wheel brand. The good news for Makstton is that we make wheels rather than interior trim or body kits. Unless a model receives a major platform or chassis change, its core wheel fitment data normally remains consistent. Based on the vehicles Makstton has measured and fitted, wheel specifications are broadly interchangeable across ZEEKR 001 model years, so this guide consolidates the key factory data into 19-, 21- and 22-inch configurations.

ZEEKR 001-003-FG CK70

Factory Wheel & Tire Specifications

Size Factory Wheel Factory Tire
19-Inch 19×8J ET45 255/55R19
21-Inch 21×8.5J ET40 255/45R21
22-Inch 22×8.5J ET40 265/40R22
Vehicle Specification Factory Data
Bolt Pattern 5×108
Center Bore 63.3mm
Gross Vehicle Weight Rating 3,030kg

The 3,030kg gross vehicle weight rating was recorded from a 2024 ZEEKR 001 675km AWD WE, the heaviest version in Makstton's collected data. Vehicle weight varies by model year and configuration, so Makstton uses this documented version when calculating the wheel load requirement.

The factory material available to Makstton does not state a per-wheel load rating. Using the documented maximum gross vehicle weight and a 20% safety factor gives 3,030 ÷ 4 × 1.2 = 909kg. Makstton therefore recommends a forged wheel load rating of at least 910kg per wheel.

For lighter factory 19-inch configurations, Makstton's 19-inch flow-formed or cast wheels rated at 850kg per wheel may be suitable after checking the vehicle's identification label and gross vehicle weight rating. The 850kg rating should not be applied automatically to every ZEEKR 001 configuration.

Center Bore Production Standard

The ZEEKR 001 and some other Geely Group vehicles should not be manufactured solely around the commonly published 63.4mm center-bore figure. Makstton has physically measured hub registers at approximately 63.26–63.28mm. A forged wheel produced at 63.4mm may fit too loosely on some vehicles and can contribute to difficult-to-diagnose vibration at higher speeds.

Based on thousands of production and installation cases, Makstton uses the following center-bore standards:

  • Forged wheels: 63.3mm
  • Flow-formed wheels: 63.35mm

The difference relates to machining methods, tolerance control and market-specific product compatibility. Makstton will explain this production standard in a separate technical article.

Measured Factory Fender Clearance

Makstton measured the distance from the outer wheel edge to the fender edge with the factory wheels installed:

Factory Wheel Front Left / Right Rear Left / Right
19×8J ET45 28 / 28mm 29 / 23mm
21×8.5J ET40 20 / 21mm 22 / 22mm
22×8.5J ET40 20 / 21mm 23 / 22mm

Small left-to-right differences are normal and may result from vehicle assembly tolerances, wheel alignment, suspension condition and measurement position.

MAKSTTON Recommended 19-, 21- and 22-Inch Fitment

Size Wheel Tire Compared with Factory
19-Inch 19×8.5J ET35 255/55R19 0.5J wider; outer edge approximately 16.4mm farther out
21-Inch 21×8.5J ET24 255/45R21 Factory width retained; outer edge approximately 16mm farther out
22-Inch 22×8.5J ET25 265/40R22 Factory width retained; outer edge approximately 15mm farther out

These recommendations were calculated from Makstton's measured factory fender clearance and verified installations. Actual tire width, tire model, suspension height, wheel alignment and individual vehicle tolerances may still affect the final position.

Real-World Fitment 01: ZEEKR 001

ZEEKR 001-002-FG FK07R

Item Front Rear
Model MAKSTTON FG FK07R
Wheel 21×9J ET30 21×9J ET23
Tire 255/45R21 255/45R21
Brake Caliper Maituo MX9 Maituo ME4
Suspension Approximately 2.5-finger gap Approximately 2.5-finger gap

Real-World Fitment 02: ZEEKR 001

ZEEKR 001-002-FG MR7

Item Front Rear
Model MAKSTTON FG MR7
Wheel 22×9.5J ET38 22×9.5J ET38
Tire 265/40R22 265/40R22
Brake Caliper Maituo MX8

Real-World Fitment 03: ZEEKR 001

ZEEKR 001-002-FG 715

Item Front Rear
Model MAKSTTON FG 715
Wheel 22×9.5J ET38 22×9.5J ET38
Tire 265/40R22 265/40R22
Suspension Factory suspension

Real-World Fitment 04: ZEEKR 001

ZEEKR 001-002-FF MR7

Item Front Rear
Model MAKSTTON FF MR7
Wheel 19×8.5J ET35 19×8.5J ET35
Tire 255/55R19 255/55R19

Fitment Notes

The data in this guide is provided for wheel customization and vehicle-fitment reference. If the final wheel position is critical, Makstton recommends measuring the individual vehicle before converting wheel width and offset. Body tolerances, wheel alignment, suspension condition and actual tire width can produce differences of several millimeters even between vehicles of the same model year and configuration.

Strictly speaking, no single fitment specification can be perfect for every vehicle.

For the ZEEKR 001, Makstton's case library contains a wide range of forged custom fitments, fixed-specification flow-formed wheels and verified installations. This guide presents only a small selection across 19-, 21- and 22-inch sizes for reference.

If you find an error in this guide or have additional verified measurement or installation data, please contact Makstton.